EC3216 MICROPROCESSORS AND APPLICATIONS SYLLABUS | ANNA UNIVERSITY BE MECHATRONICS ENGINEERING 4TH SEM SYLLABUS REGULATION 2008 2011 2012-2013 BELOW IS THE ANNA UNIVERSITY FOURTH SEMESTER B.E. MECHATRONICS ENGINEERING DEPARTMENT SYLLABUS, TEXTBOOKS, REFERENCE BOOKS,EXAM PORTIONS,QUESTION BANK,PREVIOUS YEAR QUESTION PAPERS,MODEL QUESTION PAPERS, CLASS NOTES, IMPORTANT 2 MARKS, 8 MARKS, 16 MARKS TOPICS. IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011 2012-2013 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009
EC3216 MICROPROCESSORS AND APPLICATIONS L T P C
3 0 0 3
OBJECTIVE
Most of the Mechatronics systems control is based on Microprocessor or Microcontroller. So it is
necessary to include this subject in the syllabus so that students will be exposed to the
knowledge of Microprocessor based systems and design of these systems.
UNIT I INTRODUCTION 10
Organization of Micro Computers – Organization of 8085: Architecture, Internal Register
Organization and Pin Configuration – Instruction Set of 8085 – addressing modes – instruction
and machine cycles with states and timing diagram. Methods of 8085 programs and 8085
assembly language.
UNIT II INTERFACING AND I/O DEVICES 9
Need for Interfacing - /Memory Interfacing: address space partitioning – address map – Address
decoding – Designing decoders circuit for the given address map – Bus connection and Z – line
Control – Access Time Computations.
36
I/O Interfacing: Data transfer schemes – programmed Synchronous and asynchronous –
Interrupt driven Transfer – Multiple devices and multiple interrupt levels – enabling disabiling
and masking of interrupts.
DMA transfer: Cycle stealing – Burst mode – Multiple DMA devices – DMA transfer in 8085
system – serial data transfer.
UNIT III INTERFACING DEVICES 9
Programmable peripheral device – programmable interval timer (8253) – Programmable
communication interface (USART) – Programmable interrupt controller – Programmable DMA
Controller (8257)- Programmable Keyboard/display controllers.
UNIT IV DESIGN USING PERIPHERAL DEVICES 9
Interfacing A/D and D/A converters – Matrix Keyboard design using 8255 using 8085 programs.
Designing real time clock, detecting power failure, detecting presence of objects using 8253 -
Design of Keyboard and display interfacing using 8279 – Design of digital transmission with
modems and telephone lines using 8251 A.
UNIT V MICROPROCESSOR APPLICATIONS 8
Temperature monitoring system – Automotive applications – Closed loop process control –
Stepper motor control.
TOTAL= 45 PERIODS
TEXT BOOK
1. Introduction to Microprocessor – Third Edition – Aditya P Mathur Tata McGraw – Hill
Publishing Company Ltd., New Delhi 3rd Edition 2003.
REFERENCES
1. Microprocessor Architecture. Programming and Applications with the 8085 Ramesh
Goankar, fifth edition – Penram International Publishing (India) Private Limited.
2. “Microprocessors and Interfacing, Programming and Hardware” Douglas V. Hall.Tata
McGraw – Hill Publishing Company Ltd., New Delhi, 1997.
EC3216 MICROPROCESSORS AND APPLICATIONS L T P C
3 0 0 3
OBJECTIVE
Most of the Mechatronics systems control is based on Microprocessor or Microcontroller. So it is
necessary to include this subject in the syllabus so that students will be exposed to the
knowledge of Microprocessor based systems and design of these systems.
UNIT I INTRODUCTION 10
Organization of Micro Computers – Organization of 8085: Architecture, Internal Register
Organization and Pin Configuration – Instruction Set of 8085 – addressing modes – instruction
and machine cycles with states and timing diagram. Methods of 8085 programs and 8085
assembly language.
UNIT II INTERFACING AND I/O DEVICES 9
Need for Interfacing - /Memory Interfacing: address space partitioning – address map – Address
decoding – Designing decoders circuit for the given address map – Bus connection and Z – line
Control – Access Time Computations.
36
I/O Interfacing: Data transfer schemes – programmed Synchronous and asynchronous –
Interrupt driven Transfer – Multiple devices and multiple interrupt levels – enabling disabiling
and masking of interrupts.
DMA transfer: Cycle stealing – Burst mode – Multiple DMA devices – DMA transfer in 8085
system – serial data transfer.
UNIT III INTERFACING DEVICES 9
Programmable peripheral device – programmable interval timer (8253) – Programmable
communication interface (USART) – Programmable interrupt controller – Programmable DMA
Controller (8257)- Programmable Keyboard/display controllers.
UNIT IV DESIGN USING PERIPHERAL DEVICES 9
Interfacing A/D and D/A converters – Matrix Keyboard design using 8255 using 8085 programs.
Designing real time clock, detecting power failure, detecting presence of objects using 8253 -
Design of Keyboard and display interfacing using 8279 – Design of digital transmission with
modems and telephone lines using 8251 A.
UNIT V MICROPROCESSOR APPLICATIONS 8
Temperature monitoring system – Automotive applications – Closed loop process control –
Stepper motor control.
TOTAL= 45 PERIODS
TEXT BOOK
1. Introduction to Microprocessor – Third Edition – Aditya P Mathur Tata McGraw – Hill
Publishing Company Ltd., New Delhi 3rd Edition 2003.
REFERENCES
1. Microprocessor Architecture. Programming and Applications with the 8085 Ramesh
Goankar, fifth edition – Penram International Publishing (India) Private Limited.
2. “Microprocessors and Interfacing, Programming and Hardware” Douglas V. Hall.Tata
McGraw – Hill Publishing Company Ltd., New Delhi, 1997.
No comments:
Post a Comment
Any doubt ??? Just throw it Here...