ME3301 DESIGN OF MACHINE ELEMENTS SYLLABUS | ANNA UNIVERSITY BE MECHATRONICS ENGINEERING 5TH SEMESTER SYLLABUS REGULATION 2008 2011 2012-2013 BELOW IS THE ANNA UNIVERSITY FIFTH SEMESTER BE MECHATRONICS ENGINEERING DEPARTMENT SYLLABUS, TEXTBOOKS, REFERENCE BOOKS, IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011 2012-2013 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009
ME3301 DESIGN OF MACHINE ELEMENTS L T P C
(Note: Approved Design Data Book is permitted in the
examination)
3 0 0 3
UNIT I DESIGN FUNDAMENTALS 9
Design Process - Computer aided design - Optimum design - Mechanical properties of materials
- Types of loads - Stresses - Static, varying, thermal, impact and residual - Factors of safety -
Theories of failure – Stress concentration factors.
UNIT II DESIGN OF SHAFTS,KEYS AND COUPLINGS 9
Design of Solid and Hollow shafts – Based on strength, rigidity and deflection- Torsional rigidity
– Lateral rigidity- Material constants - Design of Keys – Types – Keyways – Design of rigid and
flexible couplings
UNIT III GEARS 9
Principles of gear tooth action - Gear correction - Gear tooth failure modes - Stresses and loads
– Component design of spur, helical, bevel and worm gears. Design of speed reducers
UNIT IV BRAKES AND CLUTCHES 9
Dynamic and thermal aspects of braking – Design of brakes - Design of clutches- Single plate –
Multi plate – Conical clutch
UNIT V BEARINGS AND SPRINGS 9
Design of Bearings – Sliding contact – Rolling contact – Design of Journal Bearings –
Calculation of Bearing dimensions – Design of helical and leaf springs.
TOTAL = 45 PERIODS
REFERENCES
1. Joseph Edward Shigley and Charles R.Mischke, Mechanical Engineering Design, 6th
Edition, McGraw-Hill International Edition, 2004.
2. Kulkarni.S.G., Machine Design - Solved Problems, Tata McGraw-Hill, New Delhi, 2003.
3. William Orthwein, Machine Component Design (Vol. I & II), M/s. Jaico Publishing house,
Mumbai, 2003.
4. Maitra.G.M., and Prasad.LN., Hand Book of Mechanical Design, 2nd Edition, Tata McGraw
Hill, New Delhi, 2005.
ME3301 DESIGN OF MACHINE ELEMENTS L T P C
(Note: Approved Design Data Book is permitted in the
examination)
3 0 0 3
UNIT I DESIGN FUNDAMENTALS 9
Design Process - Computer aided design - Optimum design - Mechanical properties of materials
- Types of loads - Stresses - Static, varying, thermal, impact and residual - Factors of safety -
Theories of failure – Stress concentration factors.
UNIT II DESIGN OF SHAFTS,KEYS AND COUPLINGS 9
Design of Solid and Hollow shafts – Based on strength, rigidity and deflection- Torsional rigidity
– Lateral rigidity- Material constants - Design of Keys – Types – Keyways – Design of rigid and
flexible couplings
UNIT III GEARS 9
Principles of gear tooth action - Gear correction - Gear tooth failure modes - Stresses and loads
– Component design of spur, helical, bevel and worm gears. Design of speed reducers
UNIT IV BRAKES AND CLUTCHES 9
Dynamic and thermal aspects of braking – Design of brakes - Design of clutches- Single plate –
Multi plate – Conical clutch
UNIT V BEARINGS AND SPRINGS 9
Design of Bearings – Sliding contact – Rolling contact – Design of Journal Bearings –
Calculation of Bearing dimensions – Design of helical and leaf springs.
TOTAL = 45 PERIODS
REFERENCES
1. Joseph Edward Shigley and Charles R.Mischke, Mechanical Engineering Design, 6th
Edition, McGraw-Hill International Edition, 2004.
2. Kulkarni.S.G., Machine Design - Solved Problems, Tata McGraw-Hill, New Delhi, 2003.
3. William Orthwein, Machine Component Design (Vol. I & II), M/s. Jaico Publishing house,
Mumbai, 2003.
4. Maitra.G.M., and Prasad.LN., Hand Book of Mechanical Design, 2nd Edition, Tata McGraw
Hill, New Delhi, 2005.
No comments:
Post a Comment
Any doubt ??? Just throw it Here...