ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. ELECTRICAL AND ELECTRONICS ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009
ANNA UNIVERSITY, CHENNAI AFFILIATED INSTITUTIONS R - 2008

B.E. ELECTRICAL AND ELECTRONICS ENGINEERING
VII SEMESTERS CURRICULUM AND SYLLABI


SEMESTER VII

(Applicable to the students admitted from the Academic year 2008 – 2009 onwards)
SL.No. COURSE CODE COURSE TITLE L T P C
THEORY
1. EE2401 Power System Operation and Control 3 0 0 3
2. EE2402 Protection & Switchgear 3 0 0 3
3. EE2403 Special Electrical Machines 3 0 0 3
4. MG2351 Principles of Management 3 0 0 3
5. CS2411 Operating Systems 3 0 0 3
6. Elective – II 3 0 0 3
PRACTICAL
1. EE2404 Power System Simulation Laboratory 0 0 3 2
2. EE2405 Comprehension 0 0 2 1
TOTAL 18 0 5 21

ELECTIVE II
7. EI2311 Biomedical Instrumentation 3 0 0 3
8. EE2025 Intelligent Control 3 0 0 3
9. EE2026 Power System Dynamics 3 0 0 3
10. CS2071 Computer Architecture 3 0 0 3
11. GE2022 Total Quality Management 3 0 0 3

CS2071 COMPUTER ARCHITECTURE SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

CS2071 COMPUTER ARCHITECTURE SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. ELECTRICAL AND ELECTRONICS ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


CS2071 COMPUTER ARCHITECTURE L T P C
3 0 0 3
UNIT I INSTRUCTION SET ARCHITECTURE 9
Introduction to computer architecture - Review of digital design – Instructions and addressing –
procedures and data – assembly language programs – instruction set variations
UNIT II ARITHMETIC/LOGIC UNIT 9
Number representation – design of adders – design of simple ALUs – design of Multipliers and
dividers – design of floating point arithmetic unit
UNIT III DATA PATH AND CONTROL 9
Instruction execution steps – control unit synthesis – microprogramming – pipelining – pipeline
performance
UNIT IV MEMORY SYSTEM 9
Main Memory concepts – types of memory – cache memory organization – secondary storage –
virtual memory – paging
99
UNIT V I/O AND INTERFACES 9
I/O devices – I/O programming – polling – interrupts – DMA – buses – links – interfacing – context
switching – threads and multithreading
L = 45 T = 15 TOTAL : 60 PERIODS
TEXT BOOKS:
1. B. Parhami, “Computer Architecture”, Oxford University Press, 2005.
2. Carl Hamacher, Zvonko Vranesic and Safwat Zaky, “Computer Organization”, Fifth
Edition, Tata McGraw Hill, 2002.
REFERENCES:
1. David A. Patterson and John L. Hennessy, “Computer Organization and Design: The
Hardware/Software interface”, Third Edition, Elsevier, 2004.
2. William Stallings, “Computer Organization and Architecture – Designing for Performance”,
Seventh Edition, Pearson Education, 2006.
3. Miles Murdocca “Computers Architecture and Organization An Integrated approach”, Wiley
India pvt Ltd, 2007
4. John D. Carpinelli, “Computer systems organization and Architecture”,
Pearson Education, 2001.

EE2026 POWER SYSTEM DYNAMICS SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

EE2026 POWER SYSTEM DYNAMICS SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. ELECTRICAL AND ELECTRONICS ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


EE2026 POWER SYSTEM DYNAMICS L T P C
3 0 0 3
AIM
To understand the concept of modelling the power system and the components for simulating the
transient and dynamic behaviour of power system meant for the stability studies.
OBJECTIVES
i. To review the modeling of synchronous machine, the excitation system and speed-governing
controllers.
ii. To study small signal stability analysis of a single-machine infinite bus system with excitation
system and power system stabilizer.
iii. To study transient stability simulation of multimachine power system.
UNIT I INTRODUCTION 9
Basics of system dynamics – numerical techniques – introduction to software packages to study the
responses.
Concept and importance of power system stability in the operation and design - distinction between
transient and dynamic stability - complexity of stability problem in large system – necessity for
reduced models - stability of interconnected systems.
UNIT II SYNCHRONOUS MACHINE MODELLING 9
Synchronous machine - flux linkage equations - Park’s transformation - per unit conversion -
normalizing the equations - equivalent circuit - current space model - flux linkage state space model.
Sub-transient and transient inductances - time constants.
Simplified models (one axis and constant flux linkage) - steady state equations and phasor
diagrams.
98
UNIT III MACHINE CONTROLLERS 9
Exciter and voltage regulators - function and types of excitation systems - typical excitation system
configuration - block diagram and state space representation of IEEE type 1 excitation system -
saturation function - stabilizing circuit.
Function of speed governing systems - block diagram and state space representation of IEEE
mechanical hydraulic governor and electrical hydraulic governors for hydro turbines and steam
turbines.
UNIT IV TRANSIENT STABILITY 9
State equation for multimachine system with one axis model and simulation – modelling of
multimachine power system with one axis machine model including excitation system and speed
governing system and simulation using R-K method of fourth order (Gill’s technique) for transient
stability analysis - power system stabilizer. For all simulations, the algorithm and flow chart have to
be discussed.
UNIT V DYNAMIC STABILITY 9
System response to small disturbances - linear model of the unregulated synchronous machine and
its modes of oscillation - regulated synchronous machine - distribution of power impact - linearization
of the load equation for the one machine problem – simplified linear model - effect of excitation on
dynamic stability - approximate system representation - supplementary stabilizing signals - dynamic
performance measure - small signal performance measures.
TOTAL : 45 PERIODS
TEXT BOOKS
1. P.M. Anderson and A.A.Fouad, ‘Power System Control and Stability’, Galgotia Publications,
New Delhi, 2003.
2. P. Kundur, ‘Power System Stability and Control’, McGraw Hill Inc., USA, 1994.
REFERENCES
1. M.A.Pai and W.Sauer, ‘Power System Dynamics and Stability’, Pearson Education Asia, India,
2002.
2. James A.Momoh, Mohamed.E. EI-Hawary. “ Electric Systems, Dynamics and stability with
Artificial Intelligence applications”, Marcel Dekker, USA First
Edition 2000

EE2025 INTELLIGENT CONTROL SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

EE2025 INTELLIGENT CONTROL SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. ELECTRICAL AND ELECTRONICS ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


EE2025 INTELLIGENT CONTROL L T P C
3 0 0 3
UNIT I INTRODUCTION 9
Approaches to intelligent control. Architecture for intelligent control. Symbolic reasoning system,
rule-based systems, the AI approach. Knowledge representation. Expert systems.
UNIT II ARTIFICIAL NEURAL NETWORKS 9
Concept of Artificial Neural Networks and its basic mathematical model, McCulloch-Pitts neuron
model, simple perceptron, Adaline and Madaline, Feed-forward Multilayer Perceptron. Learning and
Training the neural network. Data Processing: Scaling, Fourier transformation, principal-component
analysis and wavelet transformations. Hopfield network, Self-organizing network and Recurrent
network. Neural Network based controller
UNIT III GENETIC ALGORITHM 9
Basic concept of Genetic algorithm and detail algorithmic steps, adjustment of free parameters.
Solution of typical control problems using genetic algorithm. Concept on some other search
techniques like tabu search and ant-colony search techniques for solving optimization problems.
UNIT IV FUZZY LOGIC SYSTEM 9
Introduction to crisp sets and fuzzy sets, basic fuzzy set operation and approximate reasoning.
Introduction to fuzzy logic modeling and control. Fuzzification, inferencing and defuzzification. Fuzzy
knowledge and rule bases. Fuzzy modeling and control schemes for nonlinear systems. Selforganizing
fuzzy logic control. Fuzzy logic control for nonlinear time-delay system.
97
UNIT V APPLICATIONS 9
GA application to power system optimisation problem, Case studies: Identification and control of
linear and nonlinear dynamic systems using Matlab-Neural Network toolbox.
Stability analysis of Neural-Network interconnection systems. Implementation of fuzzy logic controller
using Matlab fuzzy-logic toolbox. Stability analysis of fuzzy control systems.
TOTAL : 45 PERIODS TEXT BOOKS
1. Padhy.N.P.(2005), Artificial Intelligence and Intelligent System, Oxford University Press.
2. KOSKO,B. "Neural Networks And Fuzzy Systems", Prentice-Hall of India Pvt. Ltd., 1994.
REFERENCES
1. Jacek.M.Zurada, "Introduction to Artificial Neural Systems", Jaico Publishing House, 1999.
2. KLIR G.J. & FOLGER T.A. "Fuzzy sets, uncertainty and Information", Prentice-Hall of India Pvt.
Ltd., 1993.
3. Zimmerman H.J. "Fuzzy set theory-and its Applications"-Kluwer Academic Publishers, 1994.
4. Driankov, Hellendroon, "Introduction to Fuzzy Control", Narosa Publishers.
5. Goldberg D.E. (1989) Genetic algorithms in Search, Optimization and Machine
learning, Addison Wesley.

EI2311 BIOMEDICAL INSTRUMENTATION SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

EI2311 BIOMEDICAL INSTRUMENTATION SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. ELECTRICAL AND ELECTRONICS ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


EI2311 BIOMEDICAL INSTRUMENTATION L T P C
3 0 0 3
AIM:
The course is designed to make the student acquire an adequate knowledge of the physiological
systems of the human body and relate them to the parameters that have clinical importance. The
fundamental principles of equipment that are actually in use at the present day are introduced.
OBJECTIVES:
i. To provide an acquaintance of the physiology of the heart, lung, blood circulation and
circulation respiration. Biomedical applications of different transducers used.
ii. To introduce the student to the various sensing and measurement devices of electrical
origin. To provide awareness of electrical safety of medical equipments
iii. To provide the latest ideas on devices of non-electrical devices.
iv. To bring out the important and modern methods of imaging techniques.
v. To provide latest knowledge of medical assistance / techniques and therapeutic
equipments.
UNIT I PHYSIOLOGY AND TRANSDUCERS 9
Cell and its structure – Resting and Action Potential – Nervous system: Functional organisation of
the nervous system – Structure of nervous system, neurons - synapse –transmitters and neural
communication – Cardiovascular system – respiratory system – Basic components of a biomedical
system - Transducers – selection criteria – Piezo electric, ultrasonic transducers - Temperature
measurements - Fibre optic temperature sensors.
UNIT II ELECTRO – PHYSIOLOGICAL MEASUREMENTS 9
Electrodes –Limb electrodes –floating electrodes – pregelled disposable electrodes - Micro, needle
and surface electrodes – Amplifiers: Preamplifiers, differential amplifiers, chopper amplifiers –
Isolation amplifier.
ECG – EEG – EMG – ERG – Lead systems and recording methods – Typical waveforms.
Electrical safety in medical environment: shock hazards – leakage current-Instruments for checking
safety parameters of biomedical equipments
96
UNIT III NON-ELECTRICAL PARAMETER MEASUREMENTS 9
Measurement of blood pressure – Cardiac output – Heart rate – Heart sound –Pulmonary function
measurements – spirometer – Photo Plethysmography, Body Plethysmography – Blood Gas
analysers : pH of blood –measurement of blood pCO2, pO2, finger-tip oxymeter - ESR, GSR
measurements .
UNIT IV MEDICAL IMAGING 9
Radio graphic and fluoroscopic techniques – Computer tomography – MRI – Ultrasonography –
Endoscopy – Thermography – Different types of biotelemetry systems and patient monitoring –
Introduction to Biometric systems
UNIT V ASSISTING AND THERAPEUTIC EQUIPMENTS 9
Pacemakers – Defibrillators – Ventilators – Nerve and muscle stimulators – Diathermy – Heart –
Lung machine – Audio meters – Dialysers – Lithotripsy
TOTAL : 45 PERIODS
TEXT BOOKS
1. R.S.Khandpur, ‘Hand Book of Bio-Medical instrumentation’, Tata McGraw Hill Publishing Co Ltd.,
2003.
2. Leslie Cromwell, Fred J.Weibell, Erich A.Pfeiffer, ‘Bio-Medical Instrumentation and
Measurements’, II edition, Pearson Education, 2002 / PHI.
REFERENCES
1. M.Arumugam, ‘Bio-Medical Instrumentation’, Anuradha Agencies, 2003.
2. L.A. Geddes and L.E.Baker, ‘Principles of Applied Bio-Medical Instrumentation’, John Wiley &
Sons, 1975.
3. J.Webster, ‘Medical Instrumentation’, John Wiley & Sons, 1995.
4. C.Rajarao and S.K. Guha, ‘Principles of Medical Electronics and Bio-medical Instrumentation’,
Universities press (India) Ltd, Orient Longman ltd, 2000.

EE2405 COMPREHENSION SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

EE 2405 COMPREHENSION SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. ELECTRICAL AND ELECTRONICS ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


EE2405 COMPREHENSION L T P C
0 0 2 1
AIM:
To encourage the students to comprehend the knowledge acquired from the first Semester to Sixth
Semester of B.E Degree Course through periodic exercise.

EE2404 POWER SYSTEM SIMULATION LABORATORY SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

EE2404 POWER SYSTEM SIMULATION LABORATORY SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. ELECTRICAL AND ELECTRONICS ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009

EE2404 POWER SYSTEM SIMULATION LABORATORY L T P C
0 0 3 2
AIM
To acquire software development skills and experience in the usage of standard packages
necessary for analysis and simulation of power system required for its planning, operation and
control.
OBJECTIVES
i. To develop simple C programs for the following basic requirements:
a) Formation of bus admittance and impedance matrices and network solution.
b) Power flow solution of small systems using simple method, Gauss-Seidel P.F.
method.
c) Unit Commitment and Economic Dispatch.
II. To acquire experience in the usage of standard packages for the following
analysis / simulation / control functions.
d) Steady-state analysis of large system using NRPF and FDPF methods.
e) Quasi steady-state (Fault) analysis for balanced and unbalanced faults.
f) Transient stability simulation of multimachine power system.
g) Simulation of Load-Frequency Dynamics and control of power system.
1. Computation of Parameters and Modelling of Transmission Lines
2. Formation of Bus Admittance and Impedance Matrices and Solution of Networks.
3. Load Flow Analysis - I : Solution of Load Flow And Related Problems Using
Gauss-Seidel Method
81
4. Load Flow Analysis - II: Solution of Load Flow and Related Problems Using Newton-
Raphson and Fast-Decoupled Methods
5. Fault Analysis
6. Transient and Small Signal Stability Analysis: Single-Machine Infinite Bus System
7. Transient Stability Analysis of Multimachine Power Systems
8. Electromagnetic Transients in Power Systems
9. Load – Frequency Dynamics of Single- Area and Two-Area Power Systems
10. Economic Dispatch in Power Systems.
TOTAL : 45 PERIODS
DETAILED SYLLABUS
1. COMPUTATION OF PARAMETERS AND MODELLING OF TRANSMISSION
LINES
Aim
(i) To determine the positive sequence line parameters L and C per phase per kilometer of a
three phase single and double circuit transmission lines for different conductor
arrangements.
(ii) To understand modelling and performance of short, medium and long lines.
Exercises
Computation of series inductance and shunt capacitance per phase per km of a three phase line
with flat horizontal spacing for single stranded and bundle conductor configuration.
Computation of series inductance and shunt capacitance per phase per km of a three phase
double circuit transmission line with vertical conductor arrangement with bundle conductor.
Computation of voltage, current, power factor, regulation and efficiency at the receiving end of a
three phase Transmission line when the voltage and power at the sending end are given. Use П
model.
Computation of receiving end voltage of a long transmission for a given sending end voltage and
when the line is open circuited at receiving. Also compute the shunt reactor compensation to
limit the no load receiving end voltage to specified value.
Determination of the voltage profile along the long transmission line for the following cases of
loading at receiving end (i) no load (ii) rated load (iii) surge impedance loading and (iv) receiving
end short circuited.
2. FORMATION OF BUS ADMITTANCE AND IMPEDANCE MATRICES AND SOLUTION OF
NETWORKS
AIM
To understand the formation of network matrices, the bus admittance matrix Y and the bus
impedance matrix Z of a power network, to effect certain required changes on these matrices and to
obtain network solution using these matrices.
82
Exercises
2.1 Write a program in C language for formation of bus admittance matrix Y of a power network
using the “Two-Rule Method”, given the data pertaining to the transmission lines, transformers
and shunt elements. Run the program for a sample 6 bus system and compare the results with
that obtained using a standard software.
2.2 Modify the program developed in 2.1 for the following:
(i) To obtain modified Y matrix for the outage of a transmission line, a
Transformer and a shunt element.
(ii) To obtain network solution V given the current injection vector I
(iii) To obtain full Z matrix or certain specified columns of Z matrix.
Verify the correctness of the modified program using 6 bus sample system
* 2.3 Write a program in C language for forming bus impedance matrix Z using
the “Building Algorithm”.
* Optional (not mandatory)
EXPERIMENT 3
LOAD FLOW ANALYSIS - I : SOLUTION OF LOAD FLOW AND RELATED PROBLEMS USING
GAUSS-SEIDEL METHOD
Aim
(i) To understand, the basic aspects of steady state analysis of power systems that are
required for effective planning and operation of power systems.
(ii)To understand, in particular, the mathematical formulation of load flow model in complex form
and a simple method of solving load flow problems of small sized system using Gauss-Seidel
iterative algorithm
Exercises
3.1 Write a program in c language for iteratively solving load flow equations using
Gauss-Seidel method with provision for acceleration factor and for dealing
with P-V buses. Run the program for a sample 6 bus system (Base case)
and compare the results with that obtained using a standard software.
3.2 Solve the “Base case” in 3.1 for different values of acceleration factor, draw the convergence
characteristics “Iteration taken for convergence versus acceleration factor” and determine the
best acceleration factor for the system under study.
3.3 Solve the “Base Case” in 3.1 for the following changed conditions and comment on the results
obtained, namely voltage magnitude of the load buses and transmission losses:
(i) Dropping all shunt capacitors connected to network
(ii) Changing the voltage setting of generators Vgi over the range 1.00 to 1.05
(iii) Changing the tap setting of the transformers, ai, over the range 0.85 to 1.1
3.4 Resolve the base case in 3.1 after shifting generation from one generator bus to another
generator bus and comment on the MW loading of lines and transformers.
83
4. LOAD FLOW ANALYSIS – I: SOLUTION OF LOAD FLOW AND RELATED
PROBLEMS USING NEWTON-RAPHSON AND FAST DECOUPLED
METHODS
Aim
(i) To understand the following for medium and large scale power systems:
(a) Mathematical formulation of the load flow problem in real variable form
(b) Newton-Raphson method of load flow (NRLF) solution
(c) Fast Decoupled method of load flow (FDLF) solution
(ii) To become proficient in the usage of software for practical problem solving in the areas of
power system planning and operation.
(iii) To become proficient in the usage of the software in solving problems using Newton-
Raphson and Fast Decoupled load flow methods.
Exercises
4.1 Solve the load flow problem (Base case) of a sample 6 bus system using Gauss-Seidel, Fast
Decoupled and Newton-Raphson Load Flow programs for a mismatch convergence tolerance of
0.01 MW, plot the convergence characteristics and compare the convergence rate of the three
methods.
4.2 Obtain an optimal (minimum transmission loss) load flow solution for the Base case loading of 6
bus sample system by trial and error approach through repeated load flow solutions using Fast
Decoupled Load Flow package for different combinations of generator voltage settings,
transformer tap settings, and reactive power of shunt elements.
4.3 Carry out contingency analysis on the optimal state obtained in 4.2 for outage of a transmission
line using FDLF or NRLF package.
4.4 Obtain load flow solutions using FDLF or NRLF package on the optimal state obtained in 4.2 but
with reduced power factor (increased Q load) load and comment on the system voltage profile
and transmission loss.
4.5 Determine the maximum loadability of a 2 bus system using analytical solution as well as
numerical solution using FDLF package. Draw the P-V curve of the system.
4.6 For the base case operating state of the 6 bus system in 4.1 draw the P-V curve for the weakest
load bus. Also obtain the voltage Stability Margin (MW Index) at different operating states of the
system.
4.7 For the optimal operating state of 6 bus system obtained in 4.2 determine the
Available Transfer Capability (ATC) between a given “source bus” and a given “s
4. FAULT ANALYSIS
AIM
To become familiar with modelling and analysis of power systems under faulted condition and to
compute the fault level, post-fault voltages and currents for different types of faults, both
symmetric and unsymmetric.
84
Exercises
5.1 Calculate the fault current, post fault voltage and fault current through the branches for a three
phase to ground fault in a small power system and also study the effect of neighbouring system.
Check the results using available software.
5.2 Obtain the fault current, fault MVA, Post-fault bus voltages and fault current distribution for single
line to ground fault, line-to-line fault and double line to ground fault for a small power system,
using the available software. Also check the fault current and fault MVA by hand calculation.
5.3 Carryout fault analysis for a sample power system for LLLG, LG, LL and LLG faults and prepare
the report.
6. TRANSIENT AND SMALL-SIGNAL STABILITY ANALYSIS: SINGLE
MACHINE-INFINITE BUS SYSTEM
Aim
To become familiar with various aspects of the transient and small signal stability analysis of Single-
Machine Infinite Bus (SMIB) system.
Exercises
For a typical power system comprising a generating, step-up transformer, double-circuit transmission
line connected to infinite bus:
Transient Stability Analysis
6.1 Hand calculation of the initial conditions necessary for the classical model of the
synchronous machine.
6.2 Hand computation of critical clearing angle and time for the fault using equal area
criterion.
6.3 Simulation of typical disturbance sequence: fault application, fault clearance by opening of one
circuit using the software available and checking stability by plotting the swing curve.
6.4 Determination of critical clearing angle and time for the above fault sequence through trial and
error method using the software and checking with the hand computed value.
6.5 Repetition of the above for different fault locations and assessing the fault severity with respect
to the location of fault
6.6 Determination of the steady-state and transient stability margins.
Small-signal Stability Analysis:
6.7 Familiarity with linearised swing equation and characteristic equation and its roots,
damped frequency of oscillation in Hz, damping ratio and undamped natural
frequency.
6.8 Force-free time response for an initial condition using the available software.
6.9 Effect of positive, negative and zero damping.
85
7. TRANSIENT STABILITY ANALYSIS OF MULTIMACHINE POWER SYSTEMS
AIM
To become familiar with modelling aspects of synchronous machines and network, state-of-the-art
algorithm for simplified transient stability simulation, system behaviour when subjected to large
disturbances in the presence of synchronous machine controllers and to become proficient in the
usage of the software to tackle real life problems encountered in the areas of power system planning
and operation.
EXERCISES
For typical multi-machine power system:
7.1 Simulation of typical disturbance sequence: fault application, fault clearance by opening of a
line using the software available and assessing stability with and without controllers.
7.2 Determination of critical clearing angle and time for the above fault sequence through trial
and error method using the software.
7.3 Determination of transient stability margins.
7.4 Simulation of full load rejection with and without governor.
7.5 Simulation of loss of generation with and without governor.
7.6 Simulation of loss of excitation (optional).
7.7 Simulation of under frequency load shedding scheme (optional).
8. ELECTROMAGNETIC TRANSIENTS IN POWER SYSTEMS
Aim:
To study and understand the electromagnetic transient phenomena in power systems caused due to
switching and faults by using Electromagnetic Transients Program (EMTP) and to become proficient
in the usage of EMTP to address problems in the areas of over voltage protection and mitigation
and insulation coordination of EHV systems.
Exercises
Using the EMTP software or equivalent
Simulation of single-phase energisation of the load through single-phase pi-model of a transmission
line and understanding the effect of source inductance.
8.1 Simulation of three-phase energisation of the load through three-phase pi-model of a
transmission line and understanding the effect of pole discrepancy of a circuit breaker.
8.2 Simulation of energisation of an open-ended single-phase distributed parameter transmission
line and understanding the travelling wave effects.
8.3 Simulation of a three-phase load energisation through a three-phase distributed parameter
line with simultaneous and asynchronous closing of circuit breaker and studying the effects.
8.4 Study of transients due to single line-to-ground fault.
8.5 Computation of transient recovery voltage.
86
9. LOAD-FREQUENCY DYNAMICS OF SINGLE-AREA AND TWOAREA
POWER SYSTEMS
Aim
To become familiar with the modelling and analysis of load-frequency and tie-line flow dynamics of a
power system with load-frequency controller (LFC) under different control modes and to design
improved controllers to obtain the best system response.
Exercises
9.1 Given the data for a Single-Area power system, simulate the load-frequency dynamics (only
governor control) of this area for a step load disturbance of small magnitude, plot the time
response of frequency deviation and the corresponding change in turbine power. Check the
value of steady state frequency deviation obtained from simulation with that obtained by hand
calculation.
9.2 Carry out the simulation of load-frequency dynamics of the Single-Area power system in 9.1
with Load-frequency controller (Integral controller) for different values of KI (gain of the
controller) and choose the best value of KI to give an “optimal” response with regard to peak
over shoot, settling time, steady-state error and Mean-Sum-Squared-Error. [
9.3 Given the data for a two-area (identical areas) power system, simulate the load-frequency
dynamics (only governor control) of this system for a step load disturbance in one area and
plot time response of frequency deviation, turbine power deviation and tie-line power deviation.
Compare the steady-state frequency deviation obtained with that obtained in the case of
single-area system.
9.4 Carry out the simulation of load-frequency dynamics of two-area system in 9.3 for the following
control modes:
(i) Flat tie-line control
(ii) Flat frequency control
(iii) Frequency bias tie-line control
and for the frequency bias Tie-line control mode, determine the optimal values of
gain and frequency bias factor required to get the “best” time response.
9.5 Given the data for a two-area (unequal areas) power system, determine the best controller
parameters; gains and bias factors to give an optimal response for frequency deviation and tieline
deviations with regard to peak overshoot, settling time, steady-state error and Mean-
Sum-Squared-Error.
10. ECONOMIC DISPATCH IN POWER SYSTEMS
Aim
(i) To understand the basics of the problem of Economic Dispatch (ED) of optimally
adjusting the generation schedules of thermal generating units to meet the system
load which are required for unit commitment and economic operation of power
systems.
(ii) To understand the development of coordination equations (the mathematical model
for ED) without and with losses and operating constraints and solution of these
equations using direct and iterative methods
87
Exercises
10.1. Write a program in ‘C’ language to solve economic dispatch problem of a power system
with only thermal units. Take production cost function as quadratic and neglect
transmission loss.
10.2. Write a program in ‘C’ language to solve economic dispatch problem of a power system.
Take production cost as quadratic and include transmission loss using loss co-efficient.
Use λ-iteration algorithm for solving the co-ordination equations.
10.3. Determine using the program developed in exercise 10.1 the economic generation
schedule of each unit and incremental cost of received power for a sample power system,
for a given load cycle.
10.4. Determine using the program developed in exercise 10.2 the economic generation
schedule of each unit, incremental cost of received power and transmission loss for a
sample system, for the given load levels.
10.5. Apply the software module developed in 10.1 to obtain an optimum unit commitment
schedule for a few load levels.
REQUIREMENT FOR A BATCH OF 30 STUDENTS
S.No. Description of Equipment Quantity
required
1. Personal computers (Pentium-IV, 80GB, 512
MBRAM)
25
2. Printer laser 1
3. Dotmatrix 1
4. Server (Pentium IV, 80GB, 1GBRAM) (High
Speed Processor)
1
5. Software: E.M.T.P/ETAP/CYME/MIPOWER
/any power system simulation software
5 licenses
6. Compliers: C, C++, VB, VC++ 25 users

CS2411 OPERATING SYSTEMS SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

CS2411 OPERATING SYSTEMS SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. ELECTRICAL AND ELECTRONICS ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


CS2411 OPERATING SYSTEMS L T P C
3 0 0 3
Aim:
To learn the various aspects of operating systems such as process management, memory
management, file systems, and I/O management
UNIT I PROCESSES AND THREADS 9
Introduction to operating systems – review of computer organization – operating system structures –
system calls – system programs – system structure – virtual machines. Processes: Process concept
– Process scheduling – Operations on processes – Cooperating processes – Interprocess
communication – Communication in client-server systems. Case study: IPC in Linux. Threads: Multithreading
models – Threading issues. Case Study: Pthreads library
UNIT II PROCESS SCHEDULING AND SYNCHRONIZATION 10
CPU Scheduling: Scheduling criteria – Scheduling algorithms – Multiple-processor scheduling –
Real time scheduling – Algorithm Evaluation. Case study: Process scheduling in Linux. Process
Synchronization: The critical-section problem – Synchronization hardware – Semaphores – Classic
problems of synchronization – critical regions – Monitors. Deadlock: System model – Deadlock
characterization – Methods for handling deadlocks – Deadlock prevention – Deadlock avoidance –
Deadlock detection – Recovery from deadlock.
UNIT III STORAGE MANAGEMENT 9
Memory Management: Background – Swapping – Contiguous memory allocation – Paging –
Segmentation – Segmentation with paging. Virtual Memory:Background – Demand paging – Process
creation – Page replacement –Allocation of frames – Thrashing. Case Study: Memory management
in Linux
80
UNIT IV FILE SYSTEMS 9
File-System Interface: File concept – Access methods – Directory structure –File-system mounting –
Protection. File-System Implementation : Directory implementation – Allocation methods – Freespace
management – efficiency and performance – recovery – log-structured file systems. Case
studies: File system in Linux – file system in Windows XP
, UNIT V I/O SYSTEMS 8
I/O Systems – I/O Hardware – Application I/O interface – kernel I/O subsystem – streams –
performance. Mass-Storage Structure: Disk scheduling – Disk management – Swap-space
management – RAID – disk attachment – stable storage – tertiary storage. Case study: I/O in Linux
TOTAL : 45 PERIODS
TEXT BOOKS
1. Silberschatz, Galvin, and Gagne, “Operating System Concepts”, Sixth Edition, Wiley India Pvt
Ltd, 2003.
2. D. M. Dhamdhere, “Operating Systems: A concepts based approach”, Second Edition, Tata
McGraw-Hill Publishing Company Ltd., 2006.
REFERENCES
1. Andrew S. Tanenbaum, “Modern Operating Systems”, Second Edition, Pearson
Education/PHI, 2001.
2. Harvey M. Deital, “Operating Systems”, Third Edition, Pearson Education, 2004.

MG2351 PRINCIPLES OF MANAGEMENT POM SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

MG2351 PRINCIPLES OF MANAGEMENT POM SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. ELECTRICAL AND ELECTRONICS ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


MG2351 PRINCIPLES OF MANAGEMENT L T P C
3 0 0 3
UNIT I OVERVIEW OF MANAGEMENT 9
Organization - Management - Role of managers - Evolution of Management thought - Organization
and the environmental factors - Managing globally - Strategies for International Business.
UNIT II PLANNING 9
Nature and purpose of planning - Planning process - Types of plans – Objectives - Managing by
objective (MBO) Strategies - Types of strategies - Policies - Decision Making - Types of decision -
Decision Making Process - Rational Decision Making Process - Decision Making under different
conditions.
UNIT III ORGANIZING 9
Nature and purpose of organizing - Organization structure - Formal and informal groups I
organization - Line and Staff authority - Departmentation - Span of control - Centralization and
Decentralization - Delegation of authority - Staffing - Selection and Recruitment - Orientation -
Career Development - Career stages – Training - Performance Appraisal.
79
UNIT IV DIRECTING 9
Creativity and Innovation - Motivation and Satisfaction - Motivation Theories Leadership - Leadership
theories - Communication - Hurdles to effective communication - Organization Culture - Elements
and types of culture - Managing cultural diversity.
UNIT V CONTROLLING 9
Process of controlling - Types of control - Budgetary and non-budgetary control techniques -
Managing Productivity - Cost Control - Purchase Control - Maintenance Control - Quality Control -
Planning operations.
TOTAL : 45 PERIODS
TEXT BOOKS:
1. Stephen P. Robbins and Mary Coulter, 'Management', Prentice Hall of India, 8th edition.
2. Charles W L Hill, Steven L McShane, 'Principles of Management', Mcgraw Hill Education, Special
Indian Edition, 2007.
REFERENCES:
1. Hellriegel, Slocum & Jackson, ' Management - A Competency Based Approach', Thomson
South Western, 10th edition, 2007.
2. Harold Koontz, Heinz Weihrich and Mark V Cannice, ‘Management – A global &
Entrepreneurial Perspective’, Tata Mcgraw Hill, 12th edition, 2007.
3. Andrew J. Dubrin, 'Essentials of Management', Thomson Southwestern, 7th
edition, 2007.

EE 2403 SPECIAL ELECTRICAL MACHINES SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

EE 2403 SPECIAL ELECTRICAL MACHINES SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. ELECTRICAL AND ELECTRONICS ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


EE 2403 SPECIAL ELECTRICAL MACHINES L T P C
3 0 0 3
AIM
To expose the students to the construction, principle of operation and performance of special
electrical machines as an extension to the study of basic electrical machines.
OBJECTIVES
To impart knowledge on
i. Construction, principle of operation and performance of synchronous reluctance motors.
ii. Construction, principle of operation, control and performance of stepping motors.
iii. Construction, principle of operation, control and performance of switched reluctance motors.
iv. Construction, principle of operation, control and performance of permanent magnet brushless
D.C. motors.
v. Construction, principle of operation and performance of permanent magnet synchronous motors.
UNIT I SYNCHRONOUS RELUCTANCE MOTORS 9
Constructional features – Types – Axial and Radial flux motors – Operating principles – Variable
Reluctance and Hybrid Motors – SYNREL Motors – Voltage and Torque Equations - Phasor diagram
- Characteristics.
UNIT II STEPPING MOTORS 9
Constructional features – Principle of operation – Variable reluctance motor – Hybrid motor – Single
and multi stack configurations – Torque equations – Modes of excitations – Characteristics – Drive
circuits – Microprocessor control of stepping motors – Closed loop control.
78
UNIT III SWITCHED RELUCTANCE MOTORS 9
Constructional features – Rotary and Linear SRMs - Principle of operation – Torque production –
Steady state performance prediction- Analytical method -Power Converters and their controllers –
Methods of Rotor position sensing – Sensorless operation – Closed loop control of SRM -
Characteristics.
UNIT IV PERMANENT MAGNET BRUSHLESS D.C. MOTORS 9
Permanent Magnet materials – Magnetic Characteristics – Permeance coefficient -Principle of
operation – Types – Magnetic circuit analysis – EMF and torque equations –Commutation - Power
controllers – Motor characteristics and control.
UNIT V PERMANENT MAGNET SYNCHRONOUS MOTORS 9
Principle of operation – Ideal PMSM – EMF and Torque equations – Armature reaction MMF –
Synchronous Reactance – Sinewave motor with practical windings - Phasor diagram –
Torque/speed characteristics - Power controllers - Converter Volt-ampere requirements.
TOTAL : 45 PERIODS
TEXT BOOKS:
1. T.J.E. Miller, ‘Brushless Permanent Magnet and Reluctance Motor Drives’, Clarendon Press,
Oxford, 1989.
2. T. Kenjo, ‘Stepping Motors and Their Microprocessor Controls’, Clarendon Press London, 1984.
REFERENCES:
1. R.Krishnan, ‘Switched Reluctance Motor Drives – Modeling, Simulation, Analysis, Design and
Application’, CRC Press, New York, 2001.
2. P.P. Aearnley, ‘Stepping Motors – A Guide to Motor Theory and Practice’, Peter Perengrinus
London, 1982.
3. T. Kenjo and S. Nagamori, ‘Permanent Magnet and Brushless DC Motors’, Clarendon Press,
London, 1988.

EE2402 PROTECTION AND SWITCHGEAR SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

EE2402 PROTECTION AND SWITCHGEAR SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. ELECTRICAL AND ELECTRONICS ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


EE2402 PROTECTION AND SWITCHGEAR L T P C
3 0 0 3
AIM:
To introduce the students to the various abnormal operating conditions in power system and
describe the apparatus and system protection schemes. Also to describe the phenomena of current
interruption to study the various switchgears.
OBJECTIVES:
i. To discuss the causes of abnormal operating conditions (faults, lightning and switching
surges) of the apparatus and system.
ii. To understand the characteristics and functions of relays and protection schemes.
iii. To understand the problems associated with circuit interruption by a circuit breaker.
UNIT I INTRODUCTION 9
Importance of protective schemes for electrical apparatus and power system. Qualitative review of
faults and fault currents - relay terminology – definitions - and essential qualities of protection.
Protection against over voltages due to lightning and switching - arcing grounds - Peterson Coil -
ground wires - surge absorber and diverters
Power System earthing – neutral Earthing - basic ideas of insulation coordination.
UNIT II OPERATING PRINCIPLES AND RELAY CHARACTERISTICS 9
Electromagnetic relays – over current, directional and non-directional, distance, negative sequence,
differential and under frequency relays – Introduction to static relays.
UNIT III APPARATUS PROTECTION 9
Main considerations in apparatus protection - transformer, generator and motor protection -
protection of busbars. Transmission line protection - zones of protection. CTs and PTs and their
applications in protection schemes.
77
UNIT IV THEORY OF CIRCUIT INTERRUPTION 9
Physics of arc phenomena and arc interruption.
DC and AC circuit breaking - restriking voltage and recovery voltage - rate of rise of recovery voltage
- resistance switching - current chopping - interruption of capacitive current.
UNIT V CIRCUIT BREAKERS 9
Types of circuit breakers – air blast, air break, oil, SF6 and vacuum circuit breakers – comparative
merits of different circuit breakers – testing of circuit breakers. TOTAL : 45 PERIODS
TEXT BOOKS:
1. M.L. Soni, P.V. Gupta, V.S. Bhatnagar, A. Chakrabarti, ‘A Text Book on Power System
Engineering’, Dhanpat Rai & Co., 1998. (For All Chapters 1, 2, 3, 4 and 5).
2. R.K.Rajput, A Tex book of Power System Engineering. Laxmi Publications, First
Edition Reprint 2007.
REFERENCES:
1. Sunil S. Rao, ‘Switchgear and Protection’, Khanna publishers, New Delhi, 1986.
2. C.L. Wadhwa, ‘Electrical Power Systems’, Newage International (P) Ltd., 2000.
3. B. Ravindranath, and N. Chander, ‘Power System Protection & Switchgear’, Wiley Eastern Ltd.,
1977.
4. Badri Ram, Vishwakarma, ‘Power System Protection and Switchgear’, Tata McGraw Hill, 2001.
5. Y.G. Paithankar and S.R. Bhide, ‘Fundamentals of Power System Protection’, Prentice Hall of
India Pvt. Ltd., New Delhi–110001, 2003.

EE2401 POWER SYSTEM OPERATION AND CONTROL SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

EE2401 POWER SYSTEM OPERATION AND CONTROL SYLLABUS | ANNA UNIVERSITY BE EEE 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. ELECTRICAL AND ELECTRONICS ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009

EE2401 POWER SYSTEM OPERATION AND CONTROL L T P C
3 0 0 3
AIM:
To understand the day to day operation of power system and the control actions to be implemented
on the system to meet the minute-to-minute variation of system load demand.
OBJECTIVES:
i. To have an overview of power system operation and control.
ii. To model power-frequency dynamics and to design power-frequency controller.
iii. To model reactive power-voltage interaction and the control actions to be implemented for
maintaining the voltage profile against varying system load.
UNIT I INTRODUCTION 9 System load – variation - load characteristics - load curves and load-duration curve (daily,
weekly and annual) - load factor - diversity factor. Importance of load forecasting and simple
techniques of forecasting. An overview of power system operation and control and the role of
computers in the implementation. (Qualitative treatment with block diagram).
UNIT II REAL POWER - FREQUENCY CONTROL 9 Basics of speed governing mechanism and modeling - speed-load characteristics – load sharing
between two synchronous machines in parallel. Control area concept LFC control of a singlearea
system. Static and dynamic analysis of uncontrolled and controlled cases. Integration of
economic dispatch control with LFC. Two-area system – modeling - static analysis of uncontrolled
case - tie line with frequency bias control of two-area system - state variable model.
UNIT III REACTIVE POWER–VOLTAGE CONTROL 9 Basics of reactive power control. Excitation systems – modeling. Static and dynamic analysis -
stability compensation - generation and absorption of reactive power. Relation between voltage,
power and reactive power at a node - method of voltage control - tap-changing transformer. System
level control using generator voltage magnitude setting, tap setting of OLTC transformer and
MVAR injection of switched capacitors to maintain acceptable voltage profile and to minimize
transmission loss.
UNIT IV UNIT COMMITMENT AND ECONOMIC DISPATCH 9 Statement of economic dispatch problem – cost of generation – incremental cost curve co-ordination
equations without loss and with loss, solution by direct method and λ-iteration method. (No
derivation of loss coefficients). Statement of Unit Commitment problem – constraints; spinning
reserve, thermal unit constraints, hydro constraints, fuel constraints and other constraints. Solution
methods - Priority-list methods - forward dynamic programming approach. Numerical
problems only in priority-list method using full-load average production cost.
UNIT V COMPUTER CONTROL OF POWER SYSTEMS 9
Need of computer control of power systems. Concept of energy control centre (or) load dispatch
centre and the functions - system monitoring - data acquisition and control. System hardware
configuration – SCADA and EMS functions. Network topology - state estimation - security analysis
and control. Various operating states (Normal, alert, emergency, in-extremis and restorative). State
transition diagram showing various state transitions and control strategies.
TOTAL : 45 PERIODS

EE2401 POWER SYSTEM OPERATION AND CONTROL L T P C
3 0 0 3
AIM:
To understand the day to day operation of power system and the control actions to be implemented
on the system to meet the minute-to-minute variation of system load demand.
OBJECTIVES:
i. To have an overview of power system operation and control.
ii. To model power-frequency dynamics and to design power-frequency controller.
iii. To model reactive power-voltage interaction and the control actions to be implemented for
maintaining the voltage profile against varying system load.
UNIT I INTRODUCTION 9 System load – variation - load characteristics - load curves and load-duration curve (daily,
weekly and annual) - load factor - diversity factor. Importance of load forecasting and simple
techniques of forecasting. An overview of power system operation and control and the role of
computers in the implementation. (Qualitative treatment with block diagram).
UNIT II REAL POWER - FREQUENCY CONTROL 9 Basics of speed governing mechanism and modeling - speed-load characteristics – load sharing
between two synchronous machines in parallel. Control area concept LFC control of a singlearea
system. Static and dynamic analysis of uncontrolled and controlled cases. Integration of
economic dispatch control with LFC. Two-area system – modeling - static analysis of uncontrolled
case - tie line with frequency bias control of two-area system - state variable model.
UNIT III REACTIVE POWER–VOLTAGE CONTROL 9 Basics of reactive power control. Excitation systems – modeling. Static and dynamic analysis -
stability compensation - generation and absorption of reactive power. Relation between voltage,
power and reactive power at a node - method of voltage control - tap-changing transformer. System
level control using generator voltage magnitude setting, tap setting of OLTC transformer and
MVAR injection of switched capacitors to maintain acceptable voltage profile and to minimize
transmission loss.
UNIT IV UNIT COMMITMENT AND ECONOMIC DISPATCH 9 Statement of economic dispatch problem – cost of generation – incremental cost curve co-ordination
equations without loss and with loss, solution by direct method and λ-iteration method. (No
derivation of loss coefficients). Statement of Unit Commitment problem – constraints; spinning
reserve, thermal unit constraints, hydro constraints, fuel constraints and other constraints. Solution
methods - Priority-list methods - forward dynamic programming approach. Numerical
problems only in priority-list method using full-load average production cost.
UNIT V COMPUTER CONTROL OF POWER SYSTEMS 9
Need of computer control of power systems. Concept of energy control centre (or) load dispatch
centre and the functions - system monitoring - data acquisition and control. System hardware
configuration – SCADA and EMS functions. Network topology - state estimation - security analysis
and control. Various operating states (Normal, alert, emergency, in-extremis and restorative). State
transition diagram showing various state transitions and control strategies.
TOTAL : 45 PERIODS
76
TEXT BOOKS
1. Allen. J. Wood and Bruce F. Wollenberg, ‘Power Generation, Operation and Control’, John Wiley
& Sons, Inc., 2003.
2. Chakrabarti & Halder, “Power System Analysis: Operation and Control”, Prentice Hall of India,
2004 Edition.
REFERENCES
1. D.P. Kothari and I.J. Nagrath, ‘Modern Power System Analysis’, Third Edition, Tata McGraw Hill
Publishing Company Limited, New Delhi, 2003. (For Chapters 1, 2 & 3)
2. L.L. Grigsby, ‘The Electric Power Engineering, Hand Book’, CRC Press & IEEE Press, 2001.
3. Hadi Saadat, “Power System Analysis”, (For the chapters 1, 2, 3 and 4)11th Reprint
2007.
4. P.Kundur, ‘Power System Stability and Control’ MC Craw Hill Publisher, USA, 1994.
5. Olle.I.Elgerd, ‘Electric Energy Systems theory An introduction’ Tata McGraw Hill
Publishing Company Ltd. New Delhi, Second Edition 2003.

ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. MECHANICAL ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009

ANNA UNIVERSITY, CHENNAI AFFILIATED INSTITUTIONS R - 2008
B.E. MECHANICAL ENGINEERING
VII SEMESTERS CURRICULUM AND SYLLABI


SEMESTER VII
CODE NO. COURSE TITLE L T P C
THEORY
GE 2022 Total Quality Management 3 0 0 3
ME 2401 Mechatronics 3 0 0 3
ME 2402 Computer Integrated Manufacturing 3 0 0 3
ME 2403 Power Plant Engineering 3 0 0 3
Elective – II 3 0 0 3
Elective – III 3 0 0 3
PRACTICALS
ME 2404 Computer Aided Simulation & Analysis Laboratory 0 0 3 2
ME 2405 Mechatronics Lab 0 0 3 2
TOTAL 18 0 6 22


SEMESTER VII
Elective II
CODE NO. COURSE TITLE L T P C
THEORY
ME 2027 Process Planning & Cost Estimation 3 0 0 3
ME 2029 Design of Jigs, Fixtures & Press Tools 3 0 0 3
ME 2030 Composite Materials 3 0 0 3
Elective III
CODE NO. COURSE TITLE L T P C
THEORY
ME 2028 Robotics 3 0 0 3
ME 2031 Thermal Turbo machines 3 0 0 3
ME 2032 Computational Fluid Dynamics 3 0 0 3
ME 2034 Nuclear Engineering 3 0 0 3

ME2034 NUCLEAR ENGINEERING SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

ME2034 NUCLEAR ENGINEERING SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. MECHANICAL ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


ME2034 NUCLEAR ENGINEERING L T P C
3 0 0 3
OBJECTIVE
 To gain some fundamental knowledge about nuclear physics, nuclear reactor,
nuclear fuels, reactors and safe disposal of nuclear wastes.
UNIT I NUCLEAR PHYSICS 9
Nuclear model of an atom-Equivalence of mass and energy-binding- radio activity-half
life-neutron interactions-cross sections.
UNIT II NUCLEAR REACTIONS AND REACTION MATERIALS 9
Mechanism of nuclear fission and fusion- radio activity- chain reactions-critical mass and
composition-nuclear fuel cycles and its characteristics-uranium production and
purification-Zirconium, thorium, beryllium.
UNIT III REPROCESSING 9
Reprocessing: nuclear fuel cycles-spent fuel characteristics-role of solvent extraction in
reprocessing-solvent extraction equipment.
UNIT IV NUCLEAR REACTOR 9
Nuclear reactors: types of fast breeding reactors-design and construction of fast
breeding reactors-heat transfer techniques in nuclear reactors- reactor shielding. Fusion
reactors.
UNIT V SAFETY AND DISPOSAL 9
Safety and disposal: Nuclear plant safety-safety systems-changes and consequences of
accident-criteria for safety-nuclear waste-types of waste and its disposal-radiation
hazards and their prevention-weapons proliferation.
TOTAL: 45 PERIODS
TEXT BOOKS:
1. Thomas J.Cannoly, “Fundamentals of nuclear Engineering” John Wiley 1978.
REFERENCES:
1. Collier J.G., and Hewitt G.F, “Introduction to Nuclear power”, Hemisphere
86
publishing, New York. 1987
2. Wakil M.M.El., “Power Plant Technology” – McGraw-Hill International, 1984.

ME2032 COMPUTATIONAL FLUID DYNAMICS SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

ME2032 COMPUTATIONAL FLUID DYNAMICS SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. MECHANICAL ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


ME2032 COMPUTATIONAL FLUID DYNAMICS L T P C
3 0 0 3
AIM:
To impart the knowledge of numerical techniques to the solution of fluid dynamics and
heat transfer problems.
OBJECTIVES:
 To introduce Governing Equations of vicous fluid flows
 To introduce numerical modeling and its role in the field of fluid flow and heat transfer
 To enable the students to understand the various discretization methods, solution
procedures and turbulence modeling.
 To create confidence to solve complex problems in the field of fluid flow and heat
transfer by using high speed computers.
PREREQUISITE:
Fundamental Knowledge of partial differential equations, Heat Transfer and Fluid
Mechanics
UNIT I GOVERNING EQUATIONS AND BOUNDARY CONDITIONS 8
Basics of computational fluid dynamics – Governing equations of fluid dynamics –
Continuity, Momemtum and Energy equations – Chemical species transport – Physical
boundary conditions – Time-averaged equations for Turbulent Flow – Turbulent–Kinetic
Energy Equations – Mathematical behaviour of PDEs on CFD - Elliptic, Parabolic and
Hyperbolic equations.
UNIT II FINITE DIFFERENCE METHOD 9
Derivation of finite difference equations – Simple Methods – General Methods for first
and second order accuracy – solution methods for finite difference equations – Elliptic
equations – Iterative solution Methods – Parabolic equations – Explicit and Implicit
schemes – Example problems on elliptic and parabolic equations.
UNIT III FINITE VOLUME METHOD (FVM) FOR DIFFUSION 9
Finite volume formulation for steady state One, Two and Three -dimensional diffusion
problems. One dimensional unsteady heat conduction through Explicit, Crank –
Nicolson and fully implicit schemes.
UNIT IV FINITE VOLUME METHOD FOR CONVECTION DIFFUSION 10
Steady one-dimensional convection and diffusion – Central, upwind differencing
schemes-properties of discretization schemes – Conservativeness, Boundedness,
Trasnportiveness, Hybrid, Power-law, QUICK Schemes.
UNIT V CALCULATION FLOW FIELD BY FVM 9
Representation of the pressure gradient term and continuity equation – Staggered grid –
Momentum equations – Pressure and Velocity corrections – Pressure Correction
equation, SIMPLE algorithm and its variants. Turbulence models, mixing length model,
Two equation (k-Є) models – High and low Reynolds number models
TOTAL: 45 PERIODS TEXT BOOKS:
1. T.J. Chung, Computational Fluid Dynamics, Cambridge University, Press, 2002.
85
2. Versteeg, H.K., and Malalasekera, W., An Introduction to Computational Fluid
Dynamics: The finite volume Method, Longman, 1998.
3. Ghoshdastidar , P.S., computer Simulation of flow and heat transfer, Tata McGraw
Hill Publishing Company Ltd., 1998.
REFERENCES:
1. Patankar, S.V. Numerical Heat Transfer and Fluid Flow, Hemisphere Publishing
Corporation, 2004.
2. Muralidhar, K., and Sundararajan, T., computationsl Fluid Flow and Heat Transfer,
Narosa Publishing House, NewDelhi, 1995.
3. Ghoshdastidar P.S., Heat Transfer, Oxford Unversity Press, 2005.
4. Prodip Niyogi, Chakrabarty .S.K., Laha .M.K. Introduction to Computational Fluid
Dynamics, Pearson Education, 2005.
5. Introduction to Computational Fluid Dynamics Anil W. Date Cambridge University
Press, 2005.

ME 2031 THERMAL TURBO MACHINES SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

ME 2031 THERMAL TURBO MACHINES SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. MECHANICAL ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


ME 2031 THERMAL TURBO MACHINES L T P C
3 0 0 3
AIM:
To instruct the importance of the principles of various turbomachines
OBJECTIVE:
To understand the various systems, principles, operations and applications of different
types of turbo machinery components.
UNIT I PRINCIPLES 9
Energy transfer between fluid and rotor-classification of fluid machinery,-dimensionless
parameters-specific speed-applications-stage velocity triangles-work and efficiency.
UNIT II CENTRIFUGAL FANS AND BLOWERS 9
Types- stage and design parameters-flow analysis in impeller blades-volute and
diffusers, losses, characteristic curves and selection, fan drives and fan noise.
UNIT III CENTRIFUGAL COMPRESSOR 9
Construction details, impeller flow losses, slip factor, diffuser analysis, losses and
performance curves.
UNIT IV AXIAL FLOW COMPRESSOR 9
Stage velocity diagrams, enthalpy-entropy diagrams, stage losses and efficiency, work
done simple stage design problems and performance characteristics.
UNIT V AXIAL AND RADIAL FLOW TURBINES 9
Stage velocity diagrams, reaction stages, losses and coefficients, blade design
principles, testing and performance characteristics.
TOTAL: 45 PERIODS
TEXT BOOK:
1. Yahya, S.H., Turbines, Compressor and Fans, Tata McGraw Hill Publishing
Company, 1996.
REFERENCES:
1. Bruneck, Fans, Pergamom Press, 1973.
2. Earl Logan, Jr., Hand book of Turbomachinery, Marcel Dekker Inc., 1992.
3. Dixon, S.I., Fluid Mechanics and Thermodynamics of Turbomachinery, Pergamon
Press, 1990.
4. Shepherd, D.G., Principles of Turbomachinery, Macmillan, 1969.
5. Stepanpff, A.J., Blowers and Pumps, John Wiley and Sons Inc. 1965.
6. Ganesan, V., Gas Turbines, Tata McGraw Hill Pub. Co., 1999.
7. Gopalakrishnan .G and Prithvi Raj .D, A Treatise on Turbo machines, Scifech
Publications (India) Pvt. Ltd., 2002.

ME2030 COMPOSITE MATERIALS SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

ME2030 COMPOSITE MATERIALS SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. MECHANICAL ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


ME2030 COMPOSITE MATERIALS L T P C
3 0 0 3
OBJECTIVES:
 To understand the fundamentals of composite material strength and its mechanical
behavior Understanding the analysis of fiber reinforced Laminate design for different
 combinations of plies with different orientations of the fiber.
 Thermo-mechanical behavior and study of residual stresses in Laminates during
processing. Implementation of Classical Laminate Theory (CLT) to study and
82
analysis for residual stresses in an isotropic layered structure such as electronic
chips.
UNIT I INTRODUCTION, LAMINA CONSTITUTIVE EQUATIONS &
MANUFACTURING 12
Definition –Need – General Characteristics, Applications. Fibers – Glass, Carbon,
Ceramic and Aramid fibers. Matrices – Polymer, Graphite, Ceramic and Metal Matrices
– Characteristics of fibers and matrices. Lamina Constitutive Equations: Lamina
Assumptions – Macroscopic Viewpoint. Generalized Hooke’s Law. Reduction to
Homogeneous Orthotropic Lamina – Isotropic limit case, Orthotropic Stiffness matrix
(Qij), Typical Commercial material properties, Rule of Mixtures. Generally Orthotropic
Lamina –Transformation Matrix, Transformed Stiffness. Manufacturing: Bag Moulding –
Compression Moulding – Pultrusion – Filament Winding – Other Manufacturing
Processes
UNIT II FLAT PLATE LAMINATE CONSTITUTE EQUATIONS 10
Definition of stress and Moment Resultants. Strain Displacement relations. Basic
Assumptions of Laminated anisotropic plates. Laminate Constitutive Equations –
Coupling Interactions, Balanced Laminates, Symmetric Laminates, Angle Ply Laminates,
Cross Ply Laminates. Laminate Structural Moduli. Evaluation of Lamina Properties from
Laminate Tests. Quasi-Isotropic Laminates. Determination of Lamina stresses within
Laminates.
UNIT III LAMINA STRENGTH ANALYSIS 5
Introduction - Maximum Stress and Strain Criteria. Von-Misses Yield criterion for
Isotropic Materials. Generalized Hill’s Criterion for Anisotropic materials. Tsai-Hill’s
Failure Criterion for Composites. Tensor Polynomial (Tsai-Wu) Failure criterion.
Prediction of laminate Failure
UNIT IV THERMAL ANALYSIS 8
Assumption of Constant C.T.E’s. Modification of Hooke’s Law. Modification of Laminate
Constitutive Equations. Orthotropic Lamina C.T.E’s. C.T.E’s for special Laminate
Configurations – Unidirectional, Off-axis, Symmetric Balanced Laminates, Zero C.T.E
laminates, Thermally Quasi-Isotropic Laminates
UNIT V ANALYSIS OF LAMINATED FLAT PLATES 10
Equilibrium Equations of Motion. Energy Formulations. Static Bending Analysis. Buckling
Analysis. Free Vibrations – Natural Frequencies
TOTAL: 45 PERIODS TEXT BOOKS:
1. Gibson, R.F., Principles of Composite Material Mechanics, McGraw-Hill, 1994,
Second Edition - CRC press in progress.
2. Hyer, M.W., “Stress Analysis of Fiber – Reinforced Composite Materials”, McGraw-
Hill, 1998
REFERENCES:
1. Issac M. Daniel and Ori Ishai, “Engineering Mechanics of Composite Materials”,
Oxford University Press-2006, First Indian Edition - 2007
2. Mallick, P.K., Fiber –”Reinforced Composites: Materials, Manufacturing and Design”,
Maneel Dekker Inc, 1993.
3. Halpin, J.C., “Primer on Composite Materials, Analysis”, Techomic Publishing Co.,
1984.
83
4. Agarwal, B.D., and Broutman L.J., “Analysis and Performance of Fiber Composites”,
John Wiley and Sons, New York, 1990.
5. Mallick, P.K. and Newman, S., (edition), “Composite Materials Technology:
Processes and Properties”, Hansen Publisher, Munish, 1990.

ME2029 DESIGN OF JIGS, FIXTURES & PRESS TOOLS SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

ME2029 DESIGN OF JIGS, FIXTURES & PRESS TOOLS SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. MECHANICAL ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


ME2029 DESIGN OF JIGS, FIXTURES & PRESS TOOLS L T P C
3 0 0 3
OBJECTIVES:
 To understand the functions and design principles of Jigs, fixtures and press tools
 To gain proficiency in the development of required views of the final design.
UNIT I LOCATING AND CLAMPING PRINCIPLES: 8
Objectives of tool design- Function and advantages of Jigs and fixtures – Basic elements
– principles of location – Locating methods and devices – Redundant Location –
Principles of clamping – Mechanical actuation – pneumatic and hydraulic actuation
Standard parts – Drill bushes and Jig buttons – Tolerances and materials used.
UNIT II JIGS AND FIXTURES 10
Design and development of jigs and fixtures for given component- Types of Jigs – Post,
Turnover, Channel, latch, box, pot, angular post jigs – Indexing jigs – General principles
of milling, Lathe, boring, broaching and grinding fixtures – Assembly, Inspection and
Welding fixtures – Modular fixturing systems- Quick change fixtures.
81
UNIT III PRESS WORKING TERMINOLOGIES AND ELEMENTS OF
CUTTING DIES 10
Press Working Terminologies - operations – Types of presses – press accessories –
Computation of press capacity – Strip layout – Material Utilization – Shearing action –
Clearances – Press Work Materials – Center of pressure- Design of various elements of
dies – Die Block – Punch holder, Die set, guide plates – Stops – Strippers – Pilots –
Selection of Standard parts – Design and preparation of four standard views of simple
blanking, piercing, compound and progressive dies.
UNIT IV BENDING FORMING AND DRAWING DIES 10
Difference between bending, forming and drawing – Blank development for above
operations – Types of Bending dies – Press capacity – Spring back – knockouts – direct
and indirect – pressure pads – Ejectors – Variables affecting Metal flow in drawing
operations – draw die inserts – draw beads- ironing – Design and development of
bending, forming, drawing reverse re-drawing and combination dies – Blank
development for ax- symmetric, rectangular and elliptic parts – Single and double action
dies.
UNIT V MISCELLANEOUS TOPICS 7
Bulging, Swaging, Embossing, coining, curling, hole flanging, shaving and sizing,
assembly, fine Blanking dies – recent trends in tool design- computer Aids for sheet
metal forming Analysis – basic introduction - tooling for numerically controlled
machines- setup reduction for work holding – Single minute exchange of dies – Poka
Yoke - Course should be supplemented with visits to industries.
(Use of Approved design Data Book permitted).
TOTAL: 45 PERIODS
TEXT BOOKS:
1. Joshi, P.H. “Jigs and Fixtures”, Second Edition, Tata McGraw Hill Publishing Co.,
Ltd., New Delhi, 2004.
2. Donaldson, Lecain and Goold “Tool Design”, III rd Edition Tata McGraw Hill, 2000.
REFERENCES:
1. K. Venkataraman, “Design of Jigs Fixtures & Press Tools”, Tata McGraw Hill, New
Delhi, 2005.
2. Kempster, “Jigs and Fixture Design”, Hoddes and Stoughton – Third Edition 1974.
3. Joshi, P.H. “Press Tools” – Design and Construction”, Wheels publishing, 1996.
4. Hoffman “Jigs and Fixture Design” – Thomson Delmar Learning, Singapore, 2004.
5. ASTME Fundamentals of Tool Design Prentice Hall of India.
6. Design Data Hand Book, PSG College of Technology, Coimbatore.

ME2028 ROBOTICS SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

ME2028 ROBOTICS SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. MECHANICAL ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


ME2028 ROBOTICS L T P C
3 0 0 3
OBJECTIVES:
 To understand the basic concepts associated with the design and functioning and
applications of Robots To study about the drives and sensors used in Robots
 To learn about analyzing robot kinematics and robot programming
UNIT I FUNDAMENTALS OF ROBOT 7
Robot – Definition – Robot Anatomy – Co-ordinate Systems, Work Envelope, types and
classification – Specifications – Pitch, Yaw, Roll, Joint Notations, Speed of Motion, Pay
Load – Robot Parts and Functions – Need for Robots – Different Applications
UNIT II ROBOT DRIVE SYSTEMS AND END EFFECTORS 10
Pneumatic Drives – Hydraulic Drives – Mechanical Drives – Electrical Drives – D.C.
Servo Motors, Stepper Motor, A.C. Servo Motors – Salient Features, Applications and
Comparison of Drives End Effectors – Grippers – Mechanical Grippers, Pneumatic and
Hydraulic Grippers, Magnetic Grippers, Vacuum Grippers; Two Fingered and Three
Fingered Grippers; Internal Grippers and External Grippers; Selection and Design
Considerations
UNIT III SENSORS AND MACHINE VISION 10
Requirements of a sensor, Principles and Applications of the following types of sensors
– Position of sensors (Piezo Electric Sensor, LVDT, Resolvers, Optical Encoders,
Pneumatic Position Sensors), Range Sensors (Triangulation Principle, Structured,
Lighting Approach, Time of Flight Range Finders, Laser Range Meters), Proximity
Sensors (Inductive, Hall Effect, Capacitive, Ultrasonic and Optical Proximity Sensors),
Touch Sensors, (Binary Sensors, Analog Sensors), Wrist Sensors, Compliance Sensors,
Slip Sensors. Camera, Frame Grabber, Sensing and Digitizing Image Data – Signal
80
Conversion, Image Storage, Lighting Techniques. Image Processing and Analysis –
Data Reduction: Edge detection, Segmentation Feature Extraction and Object
Recognition - Algorithms. Applications – Inspection, Identification, Visual Serving and
Navigation.
UNIT IV ROBOT KINEMATICS AND ROBOT PROGRAMMING 10
Forward Kinematics, Inverse Kinematics and Differences; Forward Kinematics and
Reverse Kinematics of Manipulators with Two, Three Degrees of Freedom (In 2
Dimensional), Four Degrees of Freedom (In 3 Dimensional) – Deviations and Problems.
Teach Pendant Programming, Lead through programming, Robot programming
Languages – VAL Programming – Motion Commands, Sensor Commands, End effecter
commands, and Simple programs
UNIT V IMPLEMENTATION AND ROBOT ECONOMICS 8
RGV, AGV; Implementation of Robots in Industries – Various Steps; Safety
Considerations for Robot Operations; Economic Analysis of Robots – Pay back Method,
EUAC Method, Rate of Return Method.
TOTAL: 45 PERIODS TEXT BOOK:
1. M.P.Groover, “Industrial Robotics – Technology, Programming and Applications”,
McGraw-Hill, 2001
REFERENCES:
1. Fu.K.S. Gonzalz.R.C., and Lee C.S.G., “Robotics Control, Sensing, Vision and
Intelligence”, McGraw-Hill Book Co., 1987
2. Yoram Koren, “Robotics for Engineers”, McGraw-Hill Book Co., 1992
3. Janakiraman.P.A., “Robotics and Image Processing”, Tata McGraw-Hill, 1995

ME2027 PROCESS PLANNING AND COST ESTIMATION SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

ME2027 PROCESS PLANNING AND COST ESTIMATION SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. MECHANICAL ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


ME2027 PROCESS PLANNING AND COST ESTIMATION L T P C
(COMMON TO MECHANICAL AND PRODUCTION) 3 0 0 3
OBJECTIVE:
 To introduce the process planning concepts To make cost estimation for various
products after process planning
UNIT I WORK STUDY AND ERGONOMICS 10
Method study – Definition – Objectives-Motion economy- Principles – Tools and
Techniques-Applications – Work measurements- purpose – use – procedure – tools and
techniques- Standard time –Ergonomics – principles – applications.
UNIT II PROCESS PLANNING 10
Definition – Objective – Scope – approaches to process planning- Process planning
activities – Finished part requirements- operating sequences- machine selection –
material selection parameters- Set of documents for process planning- Developing
manufacturing logic and knowledge- production time calculation – selection of cost
optimal processes.
UNIT III INTRODUCTION TO COST ESTIMATION 7
Objective of cost estimation- costing – cost accounting- classification of cost- Elements
of cost.
79
UNIT IV COST ESTIMATION 8
Types of estimates – methods of estimates – data requirements and sources- collection
of cost- allowances in estimation.
UNIT V PRODUCTION COST ESTIMATION 10
Estimation of material cost, labour cost and over heads, allocation of overheads –
Estimation for different types of jobs.
TOTAL: 45 PERIODS
TEXT BOOKS:
1. Sinha.B.P., "Mechanical Estimating and Costing", Tata McGraw-Hill, Publishing Co.,
1995
REFERENCES:
1. Phillip.F Ostwalal and Jairo Munez, "Manufacturing Processes and systems", John
Wiley, 9th Edition, 1998
2. Russell.R.S and Tailor, B.W, "Operations Management", PHI, 4th Edition, 2003.
3. Chitale.A.V. and Gupta.R.C., "Product Design and Manufacturing", PHI, 2nd Edition,
2002.

ME2405 MECHATRONICS LABORATORY SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

ME2405 MECHATRONICS LABORATORY SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. MECHANICAL ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


ME2405 MECHATRONICS LABORATORY L T P C
(COMMON TO MECHANICAL AND PRODUCTION VI SEMESTER) 0 0 3 2
LIST OF EXPERIMENTS
1. Design and testing of fluid power circuits to control
(i) velocity (ii) direction and (iii) force of single and double acting actuators
2. Design of circuits with logic sequence using Electro pneumatic trainer kits.
3. Simulation of basic Hydraulic, Pneumatic and Electric circuits using software
4. Circuits with multiple cylinder sequences in Electro pneumatic using PLC
5. Speed Control of AC & DC drives
6. Servo controller interfacing for DC motor
7. PID controller interfacing
8. Stepper motor interfacing with 8051 Micro controller
(i) full step resolution (ii) half step resolution
9. Modeling and analysis of basic electrical, hydraulic and pneumatic systems
using LAB VIEW
10. Computerized data logging system with control for process variables like
pressure flow and temperature.
TOTAL: 45 PERIODS
69
LIST OF EQUIPMENT
(For a batch of 30 students)
1. Basic Pneumatic Trainer Kit with manual and electrical controls/
PLC Control each - 1 No.
2. Basic Hydraulic Trainer Kit - 1 No.
3. Hydraulics and Pneumatics Systems Simulation Software /
Automation studio sets - 10 No
4. 8051 - Microcontroller kit with stepper motor and drive circuit sets - 2 No.
5. LAB VIEW software with Sensors to measure Pressure,
Flow rate, direction, speed, velocity and force.seats - 2 No.

ME2404 COMPUTER AIDED SIMULATION AND ANALYSIS LABORATORY SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

ME2404 COMPUTER AIDED SIMULATION AND ANALYSIS LABORATORY SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. MECHANICAL ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


ME2404 COMPUTER AIDED SIMULATION AND ANALYSIS LABORATORY L T P C
 0 0 3 2
LIST OF EXPERIMENTS
A. SIMULATION 8
Simulation of Air conditioning system with condenser temperature and evaporator
temperatures as input to get COP using C /MAT Lab.
Simulation of Hydraulic / Pneumatic cylinder using C / MAT Lab.
Simulation of cam and follower mechanism using C / MAT Lab.
68
B. ANALYSIS (SIMPLE TREATMENT ONLY) 37
1. Stress analysis of a plate with a circular hole.
2. Stress analysis of rectangular L bracket
3. Stress analysis of an axi-symmetric component
4. Stress analysis of beams (Cantilever, Simply supported, Fixed ends)
5. Mode frequency analysis of a 2 D component
6. Mode frequency analysis of beams (Cantilever, Simply supported, Fixed ends)
7. Harmonic analysis of a 2D component
8. Thermal stress analysis of a 2D component
9. Conductive heat transfer analysis of a 2D component
10. Convective heat transfer analysis of a 2D component
TOTAL: 45 PERIODS
LIST OF EQUIPMENTS
(For a batch of 30 students)
Computer System 30
17” VGA Color Monitor
Pentium IV Processor
40 GB HDD
512 MB RAM
Color Desk Jet Printer 01
Software
Suitable analysis software 30 licenses
C / MATLAB 5 licenses

ME2403 POWER PLANT ENGINEERING SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

ME2403 POWER PLANT ENGINEERING SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. MECHANICAL ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


ME2403 POWER PLANT ENGINEERING L T P C
3 0 0 3
OBJECTIVE:
 To understand the various components , operations and applications of different
types of power plants
67
UNIT I INTRODUCTION TO POWER PLANTS AND BOILERS 9
Layout of Steam , Hydel , Diesel , MHD, Nuclear and Gas turbine Power Plants
Combined Power cycles – comparison and selection , Load duration Curves Steam
boilers and cycles – High pressure and Super Critical Boilers – Fluidised Bed Boilers
UNIT II STEAM POWER PLANT 9
Fuel and ash handling ,Combustion Equipment for burning coal, Mechanical Stokers.
Pulveriser, Electrostatic Precipitator, Draught- Different Types, Surface condenser
types, cooling Towers
UNIT III NUCLEAR AND HYDEL POWER PLANTS 9
Nuclear Energy-Fission , Fusion Reaction, Types of Reactors, Pressurized water reactor
,Boiling water reactor, Waste disposal and safety Hydel Power plant- Essential
elements, Selection of turbines, governing of Turbines- Micro hydel developments
UNIT IV DIESEL AND GAS TURBINE POWER PLANT 9
Types of diesel plants, components , Selection of Engine type, applications-Gas turbine
power plant- Fuels- Gas turbine material – open and closed cycles- reheating –
Regeneration and intercooling – combines cycle
UNIT V OTHER POWER PLANTS AND ECONOMICS OF POWER PLANTS 9
Geo thermal- OTEC- tidel- Pumped storage –Solar central receiver system Cost of
electric Energy- Fixed and operating costs-Energy rates- Types tariffs- Economics of
load sharing, comparison of various power plants.
TOTAL: 45 PERIODS
TEXT BOOKS:
1. Arora S.C and Domkundwar S, “A Course in Power Plant Engineering”, Dhanpat
Rai, 2001
2. Nag P.K ,”Power Plant Engineering”. Third edition Tata McGraw- Hill ,2007
REFERENCES:
1. EI-Wakil M.M ,Power “Plant Technology,” Tata McGraw-Hill 1984
2. K.K.Ramalingam , “ Power Plant Engineering “, Scitech Publications, 2002
3. G.R,Nagpal , “Power Plant Engineering”, Khanna Publishers 1998
4. G.D.Rai, “Introduction to Power Plant technology” Khanna Publishers, 1995

ME2402 COMPUTER INTEGRATED MANUFACTURING SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012

ME2402 COMPUTER INTEGRATED MANUFACTURING SYLLABUS | ANNA UNIVERSITY BE MECHANICAL ENGINEERING 7TH SEMESTER SYLLABUS REGULATION 2008 2011-2012 BELOW IS THE ANNA UNIVERSITY SEVENTH SEMESTER B.E. MECHANICAL ENGINEERING DEPARTMENT SYLLABUS IT IS APPLICABLE FOR ALL STUDENTS ADMITTED IN THE YEAR 2011-2012 (ANNA UNIVERSITY CHENNAI,TRICHY,MADURAI,TIRUNELVELI,COIMBATORE), 2008 REGULATION OF ANNA UNIVERSITY CHENNAI AND STUDENTS ADMITTED IN ANNA UNIVERSITY CHENNAI DURING 2009


ME2402 COMPUTER INTEGRATED MANUFACTURING L T P C
3 0 0 3 OBJECTIVE:
 This course will enable the student
 To gain knowledge about the basic fundamental of CAD.
 To gain knowledge on how computers are integrated at various levels of planning
and manufacturing understand computer aided planning and control and computer
monitoring.
UNIT I COMPUTER AIDED DESIGN 9
Concept of CAD as drafting and designing facility, desirable features of CAD package,
drawing features in CAD – Scaling, rotation, translation, editing, dimensioning, labeling,
Zoom, pan, redraw and regenerate, typical CAD command structure, wire frame
modeling, surface modeling and solid modeling (concepts only) in relation to popular
CAD packages.
UNIT II COMPONENTS OF CIM 9
CIM as a concept and a technology, CASA/Sme model of CIM, CIM II, benefits of CIM,
communication matrix in CIM, fundamentals of computer communication in CIM – CIM
data transmission methods – seriel, parallel, asynchronous, synchronous, modulation,
demodulation, simplex and duplex. Types of communication in CIM – point to point
(PTP), star and multiplexing. Computer networking in CIM – the seven layer OSI model,
66
LAN model, MAP model, network topologies – star, ring and bus, advantages of
networks in CIM
UNIT III GROUP TECHNOLOGY AND COMPUTER AIDED PROCESS
PLANNING 9
History Of Group Technology – role of G.T in CAD/CAM Integration – part familiesclassification
and coding – DCLASS and MCLASS and OPTIZ coding systems – facility
design using G.T – benefits of G.T – cellular manufacturing.Process planning - role of
process planning in CAD/CAM Integration – approaches to computer aided process
planning – variant approach and generative approaches – CAPP and CMPP systems.
UNIT IV SHOP FLOOR CONTROL AND INTRODUCTION TO FMS 9
shop floor control – phases – factory data collection system – automatic identification
methods – Bar code technology – automated data collection system.
FMS – components of FMS – types – FMS workstation – material handling and storage
system –FMS layout- computer control systems – applications and benefits.
UNIT V COMPUTER AIDED PLANNING AND CONTROL AND COMPUTER
MONITORING 9
Production planning and control – cost planning and control – inventory management –
material requirements planning (MRP) – shop floor control. Lean and Agile
Manufacturing. Types of production monitoring systems – structure model of
manufacturing – process control and strategies – direct digital control.
TOTAL: 45 PERIODS
TEXT BOOK:
1. Mikell. P. Groover “Automation, Production Systems and Computer Integrated
Manufacturing”, Pearson Education 2001.
REFERENCES:
1. Mikell. P. Groover and Emory Zimmers Jr.,“CAD/CAM”, Prentice hall of India Pvt.
Ltd., 1998.
2. James A. Regh and Henry W. Kreabber, “Computer Integrated Manufacturing”,
Pearson Education second edition, 2005.
3. Chris McMahon and Jimmie Browne, “CAD CAM Principles, Practice and
Manufacturing Management”, Pearson Education second edition, 2005.
4. Ranky, Paul G., “Computer Integrated Manufacturing”, Prentice hall of India Pvt. Ltd.,
2005.
5. Yorem Koren, “ Computer Integrated Manufacturing”, McGraw Hill, 2005.
6. P N Rao, “ CAD/CAM Principles and Applications”, TMH Publications, 2007.